Browse all practice questions for the FDNY COF for Fire Alarm Systems Inspection, Testing and Service Technician (S-98) Practice Exam. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

FDNY COF for Fire Alarm Systems Inspection, Testing and Service Technician (S-98) Practice Exam course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • How should you approach a fire alarm system that is in trouble condition before performing further work?
  • Which of the following is a primary purpose of the trouble memory?
  • Based on FC802 definitions, which is not a cause of an unwarranted alarm?
  • Name two common fire detector types used to detect smoke.
  • In combined fire protection systems, what is the function of a water flow switch?
  • Secondary power supplies for emergency voice evacuation systems must operate in a non-alarm condition for how many hours and, under maximum load, for a minimum of how many minutes?
  • Which option is NOT part of the recommended handling of unused devices?
  • What type of tests are commonly performed to verify the functionality of all initiating devices?
  • Which statement about remote supervising station staffing is correct?
  • A digital alarm communicator transmitter shall be connected to how many separate means of transmission at the protected premises?
  • According to fire code and fire rules, who is responsible for preventing unnecessary and unwanted alarms?
  • What is an annunciator in a fire alarm system?
  • For elevator recall in firefighter service, which three detector locations are used to recall elevators, unless the AHJ requires otherwise?
  • In NYC, which document confirms the fire alarm system has passed acceptance testing by the FDNY?
  • Which metal is commonly used as a reliable electrical conductor in wiring?
  • The term 'Stooped' describes which type of ceiling?
  • What is the purpose of an addressable fire alarm device?
  • The phrase 'as built design and installation documents and equipment specifications' refers to which type of content?
  • Visible signaling appliances installed in corridors less than 20 feet long must be installed within what distance of the end of the corridor, with what maximum separation between appliances?
  • Which of the following statements about the trouble memory is false?
  • Which statement best describes the function of the trouble memory in a fire alarm panel?
  • Who is typically the AHJ for fire alarm permits in NYC?
  • If a monitored conductor experiences a single open or ground fault, what indication is expected?
  • What two actions must a digital alarm communicator transmitter perform?
  • What is the role of an addressable fire alarm device?
  • What is the minimum interval for automatic test transmissions by a digital alarm communicator transmitter?
  • Why is coordination with the building's life safety team important during testing?
  • Pre-signal system installations require approval from which official?
  • Ionization smoke detectors are examples of which type of detection in this context?
  • When a modification or addition is made to a fire alarm system, which action is essential to maintain regulatory compliance?
  • In the typical sequence of operation when a smoke detector is triggered in an automatic fire alarm system, what is the first action?
  • How should a technician document a system modification or addition to the fire alarm system?
  • If heat detectors shut down elevator power prior to sprinkler operation, the detector shall be placed within how many feet of each sprinkler head?
  • According to NFPA chapter 4, batteries shall be permanently marked with which information?
  • According to section 901.6.2, records of system inspections, testing, servicing or other maintenance must be maintained on the premise for a period of years?
  • What is the maximum number of water flow switches permitted on a single IDC?
  • Within how many hours after batteries have been fully discharged should the control panel charging apparatus be recharged?
  • During the sequence of operation, what is activated after the initiating device signals the control panel?
  • What is the primary purpose of a heat detector in a fire alarm system?
  • Which statement about the trouble memory is false?
  • What is the purpose of a permit-to-test in NYC and why is it required?
  • What type of detector is primarily used for fast detection of flaming fires?
  • What type of drawing typically shows correct conductor counts?
  • Which statement best describes the proper handling of unused devices until installation or removal?
  • During an inspection, which item helps maintain traceability for uninstalled devices?
  • In ceiling detector layouts, heat detectors should be placed so that row detectors are within how many feet of the peak?
  • If multiple visible signaling appliances are in the same field of view, how must they operate relative to one another?
  • The ongoing maintenance obligation for fire and life safety systems is assigned to which party?
  • Which statement best describes the two common smoke detector types?
  • What is the purpose of tagging an uninstalled device during inspection?
  • What is the recommended wording in records to reflect the status of an uninstalled device?
  • Public mode audible devices shall have a sound level at least how many decibels above the average ambient sound level, or above the maximum sound level for 60 seconds, whichever is greater?
  • What is the difference between 'quarterly test' and 'annual test' in routine inspection schedules?
  • Which candela rating would be used for a visible alarm appliance in a 20' × 20' room?
  • For visible signaling appliances, the flash rate shall not exceed and shall not be less than what values across the listed voltage range?
  • What is the role of a notification appliance in a fire alarm system?
  • What describes a circuit where signals from multiple devices are transmitted without identifying the activated device?
  • If a digital alarm communicator transmitter calls a number that is forwarded to the receiver, how often must the integrity of the call forwarding be verified?
  • Why is it important to avoid disturbing a system that is in alarm or being reset without proper authority or procedure?
  • What is a Class A circuit in fire alarm wiring?
  • How many water flow switches are allowed on a single IDC?
  • After a trouble condition is cleared, what is the recommended step before signaling or testing again?
  • The occurrence of a single open or single ground fault condition in installation conductors must be automatically indicated within how many seconds?
  • An initiating device that is destroyed as a result of its operation is what type?
  • Which documents are included as part of the required information to be provided?
  • Which circuit provides power to audible/visual notification appliances?
  • Which statement is NOT a qualification for the S98 certificate of fitness?
  • Before stepping away from a system in trouble condition, what is the recommended practice?
  • Is a digital alarm communicator transmitter serving an office building, owned by the building owner and connected to tenant-owned telephone lines, compliant with NFPA 72?
  • What unit of measurement is used to express the output rating of visible signaling devices?
  • What is the minimum distance for mounting a spot-type smoke detector from an air supply diffuser?
  • Which statement best describes the goal of a functional test in a fire alarm system?
  • Who may require deviation from the standard locations for elevator recall detectors, if applicable?
  • What is the purpose of testing the response of notification appliances during a functional test?
  • Where shall inspection, testing, and maintenance instructions and related documents be provided?
  • If you fail the written test you will not be permitted to retest for how many days?
  • Which person is charged with ensuring proper safety precautions when a fire protection system is out of service?
  • Which of the following is NOT a typical sign that a fire alarm battery is failed and needs replacement?
  • What component is used to test water flow devices by allowing water to flow during testing?
  • Complete records of all signals received at a supervising station must be retained for at least how long?
  • What are the three main subsystems of a typical fire alarm system?
  • Which standard forms the basis for fire alarm system design, installation, testing, and maintenance referenced by the FDNY S-98 exam?
  • Where is an annunciator panel typically located in a fire alarm system?
  • When reporting uninstalled devices, what should be included in the records?
  • Which component processes signals from initiating devices and coordinates alarm responses?
  • Why is a 'trouble' signal important in fire alarm supervision?
  • Which statement accurately reflects the location requirement for essential documents?
  • Under the New York City Fire Code, which testing method is not permitted for smoke detectors?
  • What is the maximum distance allowed for a shunt loop circuit?
  • A digital alarm communicator transmitter shall automatically initiate and complete a test signal transmission to its associated receiver at least once every how many hours?
  • Which of the following are initiating devices?
  • What type of permit is typically required to perform any work on a fire alarm system in NYC?
  • A S98 certificate of fitness holder may perform all the following functions except:
  • A listed relay used to initiate fire safety functions shall be located within how many feet of the controlled circuit or appliance?
  • What information should technicians record on a test tag or report for each device tested?
  • What information should be included on a fire alarm system test tag or report?
  • Which document confirms acceptance testing by the FDNY in NYC after a system is installed?
  • Why is it important to maintain records indicating the status of unused devices?
  • What does sensitivity testing of smoke detectors ensure?
  • During a field inspection, a fault is recorded in the trouble memory. What is the appropriate action?
  • What does a Signaling Line Circuit (SLC) do in addressable fire alarm systems?
  • Which labeling requirement is also required for Autubel devices besides sound pressure level?
  • What is the purpose of labeling and identifying devices during inspection?
  • Name the three types of signals created by a fire alarm system.
  • Which device labeling requirement is specifically associated with Autubel devices?
  • What does FACP stand for in typical fire alarm systems?
  • Secondary power supplies are required to have sufficient power to operate the fire alarm system in a non alarm condition for how many hours and then be capable of operating all notification devices for a minimum of how many minutes?
  • A coded alarm signal shall consist of not less than how many rounds, and each round shall have not less than how many impulses?
  • All of the following are good conductors of electricity except which material?
  • Building evacuation signals must meet the ANSI 53.41 Temporal 3 signal for which type of system notification?
  • Which of the following is NOT an example of line-type detection?
  • Records of inspections, testing, servicing, or maintenance must be retained on site for how long?
  • What is the function of the Fire Alarm Control Panel (FACP)?
  • According to NFPA 72 Chapter 9, where must the shunt circuit conductors of auxiliary fire alarm systems be installed?
  • Secondary power supply shall automatically provide power to the protected premises fire alarm system within how many seconds when primary power fails?
  • If maintenance documents need to be accessed readily during work, where should they be located?
  • Electrical equipment must be capable of operating at what percentage of its nameplate voltage?
  • A signaling line circuit is a circuit to which automatic or manual initiating devices are connected where the signal received does what?
  • The time period before you may retake the written exam after a failure is 90 days.
  • Which option would be a compliant approach for pre-signal system installations?
  • The owner is primarily responsible for what aspect of fire and life safety systems?
  • Upon receipt of a trouble signal, within how many hours must maintenance personnel arrive to initiate service?
  • Fire pumps shall be supervised for which supervisory signal?
  • Who is responsible for making entries in the smoke detector maintenance log if there is no Fire Safety Director?
  • Which statement about permit-to-test is true?
  • Who is responsible for ensuring fire and life safety systems are maintained in good working order at all times?
  • Under NFPA chapter 4, which information must be permanently marked on batteries?
  • When is the NFPA 72 record of completion prepared?
  • Which type of document is included among the required information to be provided on site?
  • What is the purpose of including a 'next due date' on a fire alarm test tag or report?
  • A bean is defined as a structural member that could drop into the room’s base more than how many inches and be located more than how many feet apart on center?
  • Which test validates that a newly installed or modified fire alarm system meets code and is acceptable to the AHJ?
  • The time from off-hook to on-hook per attempt for a digital alarm communicator transmitter must not exceed how many seconds?
  • Which detector type is typically more sensitive to slow, smoldering fires?
  • Which candela reading and how many visible appliances are required for a visible alarm in a 20' × 20' room?
  • Which device is used to manually initiate a fire alarm?
  • Who is responsible for making entries in the smoke detector maintenance log if no Fire Safety Director is appointed, according to fire rules?
  • NFPA 72 sets a maximum travel distance to the nearest fire alarm box from any point as which of the following?
  • How should water flow devices be tested?
  • What is central station monitoring?
  • Which action is described as incorrect for control station handling of an alarm signal?
  • What is an acceptance test?
  • NFPA 72 requires manual fire alarm boxes to be conspicuous, unobstructed, and ________.
  • In NYC, what is the purpose of documenting test results with a next due date on each device?
  • What is the maximum candela (cd) rating allowed for a visible signaling appliance?
  • When heat detectors are used to shut down elevator power prior to sprinkler operation, the detector shall have both a ________ ________ ___________ and a __________ _____________ as compared to the sprinkler.
  • Pre-signal systems may be installed under which condition?
  • Which of the following is an example of an initiating device?
  • Where should a listed relay that initiates fire safety functions be located in relation to the controlled circuit?
  • When testing for proper calibration of smoke detectors, which option would be disallowed?
  • When installing heat detectors on ceilings, a row detector should be located within how many feet of the ceiling peak?
  • What is the purpose of the 'trouble' memory in a fire alarm control panel?
  • What is the importance of maintaining a clean test environment and not contaminating detectors during testing?
  • What is an elevator recall and when is it used?
  • Which statement accurately lists the three signals produced by a fire alarm system?
  • What does SLC stand for in addressable fire alarm systems?
  • Which drawing is specifically used to convey the vertical distribution of circuits and conductor counts across floors?
  • What is one of the name plate requirements for audible appliances?
  • During inspection, how should uninstalled or unused devices be handled?
  • Which wiring methods are permitted for shunt circuit conductors of auxiliary fire alarm systems?
  • What is a Class B circuit in fire alarm wiring?
  • What is the primary purpose of the smoke detector maintenance log?
  • Wall mounting of visible signaling appliances must place the lens within what height range above the finished floor?
  • Which statement correctly describes the three locations that may be used to recall elevators for firefighter service recall?
  • Which statement best reflects the required minimum hours for non-alarm operation of a standard fire alarm secondary power supply?
  • In a Class B circuit, what happens if a fault occurs?
  • What is the smallest conductor size allowed for shunt type circuits?
  • Who is responsible for reporting an out-of-service fire protection system to the fire department and when must it be reported?
  • Remote supervising stations are required to be manned at all times; what is the minimum number of trained persons on duty?
  • What is a functional test and what should it verify in a fire alarm system?
  • What does 'supervision' mean in fire alarm circuits?
  • In the same room scenario, how many visible appliances are required?
  • Which authority has the stated role in approving pre-signal system installations?
  • If a fault is recorded in the trouble memory, what is the recommended action?
  • What is the purpose of maintaining a detailed service log for a fire alarm system?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy